| R1, R10, R11 |
390 Ohm, 0.25W, 1% |
|
| R14-16, R23-26, R32-34 |
75 Ohm, 0.25W, 1% |
|
| R4-6 |
180 Ohm, 0.25W, 1% |
|
| R2-3, R29-30, R35-36 |
220 Ohm, 0.25W, 5% |
|
| R12-13 |
50 Ohm, 0.25W, 1% |
|
| R17-22 |
1k Ohm, 0.25W, 1% |
|
| R27-28 |
1M Ohm, 0.25W, 5% |
|
| R31 |
681k Ohm, 0.25W, 1% |
|
| R7-9 |
250 Ohm, 1W linear potentiometer |
|
| C1-4, C11, C14, C16-17, C19, C24 |
0.1μ F, ceramic |
|
| C12, C15, C18, C20, C25, C26 |
10μ F, tantalum |
|
| C5, C8 |
47p F, ceramic |
|
| C6-7 |
56p F, ceramic |
|
| C13 |
56n F, ceramic |
|
| C21-23 |
220μ F, aluminum electrolytic |
|
| C27 |
10n F, polyester |
|
| C28 |
2.2μ F, tantalum |
Takes 12V. Value for Tantalum, check LM7905 datasheet otherwise. |
| C29 |
1μ F, tantalum |
Value for Tantalum, check LM7905 datasheet otherwise. |
| C9-10 |
Adjustable, ~15p F |
|
| L1 |
~40m H |
See comments here |
| D1 |
1N4148 |
1N4004 will work too, basically any diode with forward voltage > ~0.7V |
| LED1-4 |
Any LED will do |
|
| Q1 |
14.318180 MHz HC49 crystal |
|
| Q2 |
17.734475 MHz HC49 crystal |
|
| TR1-2 |
1:1 100 mW audio transformer |
e.g. TY-145P 600/600 Ohm |
| AUDIO_SW, STND_SW |
ON-ON DPDT |
|
| CREDIT_SW |
MOM-OFF-MOM SPDT mini |
|
| PWR_SW |
ON-ON SPDT mini |
|
| TEST_SW |
MOM-OFF-MOM DPDT |
|
| AD725 |
AD725ARZ RGB encoder |
|
| AO |
AD8073JNZ triple video amplifier |
|
| EL1883 |
EL1883ISZ video sync separator |
|
| IC1 |
MM74HC04N CMOS hex-inverter |
|
| IC2 |
LM7905 -5V linear regulator |
|
| ATX |
5566 MiniFit 20-pin header (female) |
Specific P/N#: 39281203 |
| A_OUT |
Dual female RCA plug, right angled |
Specific part was “Pro Signal PSG01548” |
| COMP |
Single female RCA plug, right angled |
Specific part was “Pro Signal PSG01547” |
| SVID |
MiniDin 4-pin female plug, right angled |
Specific part was “Pro Signal PSG01571” |
| PERITEL |
TV SCART female connector, right angled |
Specific part was “Pro Signal PSG01601” |
| P1-2 |
Sub-D DB15 female plug, right angled |
|
| X1 |
WAGO 233-524 |
|
| X2 |
WAGO 233-508 |
|
| X3 |
WAGO 233-506 |
|